SKF 99210 Speedi Sleeve Kit for 2.125in Shaft, 0.5in Width

From a wide range of products and a commitment to continuous innovation, we have positioned ourselves as a preferred partner for leading vehicle aftermarket distributors worldwide. The SKF vehicle aftermarket proudly offers over 20,000 product variations, all of which are characterized by unmatched quality.

We prioritize delivering system repair products that cover a broad spectrum, ensuring you won't need to search extensively for the components you require. Supported by a robust network of over 10,000 distributors and dealers, our automotive spare parts for cars, trucks, and two-wheelers are delivered to workshops across the globe.

Looking for the Right Product for Your Vehicle?
To find the most suitable product, you can easily enter your vehicle's information into our site’s search function.

Need Product Fit Confirmation?
Feel free to send us a message, and we’ll verify compatibility for you.

Are SKF Products Comparable to OEM?
Absolutely, SKF products boast quality equivalent to Original Equipment (OE) standards.

Product Overview: Understanding the Speedi-Sleeve
The following are the installation steps for an SKF SPEEDI-SLEEVE:

1. Begin by cleaning the seal counter surface on the shaft, removing any burrs or rough spots.
2. Measure the diameter at an unworn section of the shaft, averaging readings from three different points to ensure the shaft is within recommended specifications. A proper sleeve size will provide an adequate press fit without the need for adhesive.
3. Identify the correct position for the sleeve to cover the seal wear track accurately. This involves precise measurement or marking on the shaft surface, ensuring the sleeve is placed directly over the worn area rather than just being flush with the end.
4. If wear grooves are shallow, they do not require filling; however, you can optionally apply a thin layer of non-hardening sealant, like Loctite 209, on the sleeve's inside diameter. Make sure to clean any excess sealant that may migrate to the exterior surfaces.
5. For deeper scores, use a powdered metal epoxy type filler to fill the grooves. The sleeve should be installed before the filler hardens to allow it to wipe any excess.
6. Start the installation with the flange end of the sleeve presented on the shaft. Then, place the installation tool over the sleeve.
7. Gently tap the center of the installation tool to position the sleeve correctly over the seal-worn surface. If needed, a length of pipe or tubing with a clean, squared-off end can be used as an extension for the installation tool, ensuring the diameters match. Take care not to scratch the precision-ground exterior of the sleeve.
8. Keep the flange intact unless clearance adjustments are necessary. If you need to remove it, cut perpendicular to the tear-off groove using metal shears without touching the finished sleeve surface. Once positioned, standard pliers can be used to bend the flange, allowing it to detach cleanly.
9. After fitting the sleeve, recheck for any burrs that could compromise the seal.
10. Lubricate the sleeve with the system medium prior to its installation.
11. Finally, proceed with the sealing installation.

Determining the Right Size
To ascertain the correct sleeve size, make sure to clean the shaft thoroughly. Measure the diameter of an undamaged section of the seal counterface in at least three planes, averaging these measurements to establish your SKF Speedi-Sleeve size. If it falls within the acceptable range outlined in the product table, there will be a sufficient tight fit on the shaft, negating the need for adhesive.

The SKF SPEEDI-SLEEVE is a rapid and efficient solution for refurbishing worn shafts. It provides an enhanced sealing surface and is significantly quicker than methods such as remetalizing or regrinding. The sleeve's external surface ensures an optimal seal—a crucial advantage over many traditional finishing techniques prone to sealing issues.

Covering shaft diameters from .472” to 8” (12 mm to 200 mm), the SKF SPEEDI-SLEEVE is made of high-quality stainless steel with a thin-walled design of 0.011” (0.28 mm). Boasting wear-resistant contact surfaces and a finish of Ra 10 to 20 µin (0.25 to 0.5 µm), the installation process requires no expensive machining or extensive preparation. As installation takes just a few minutes, it effectively minimizes downtime in your operations.

The SKF SPEEDI-SLEEVE serves as a reliable and cost-effective option, swiftly slipped over the worn area to provide a surface even harder than that of a new shaft. Each SPEEDI-SLEEVE set includes a disposable installation tool to ensure a straightforward installation process. Careful application is necessary, but with the included tool, achieving desired results is uncomplicated.

product information: